
Water Heater Leaking? What to Do Right Away in Overland Park
Puddle around your Overland Park water heater? Close the cold-water valve, shut off the fuel, then call or text and you'll get a call right back.
Updated Prices checked
- Basement, closet and garage leaks
- Phone answered day and night
- Price before any work starts
Water heater trouble?
Leaking right now? Three things before anything else
- Shut off the water. Turn the cold-water supply valve on the pipe at the top of the heater clockwise until it stops.
- Cut the power. Electric unit: switch off its breaker at the panel. Gas unit: turn the gas control knob on the front of the heater to OFF.
- Then call or text (913) 794-3707. Answered 24/7, and you'll get a call right back.
Smell gas? Leave the house, don't flip any switches, and call 911 and then your gas company's leak line at 888-482-4950 (Kansas Gas Service) or 866-322-8667 (Atmos Energy) from outside.
The water in the pipes here matters to a leak. WaterOne's 2025 water quality report (opens in a new tab), which covers 2024, puts average hardness at 144 parts per million, about 8.4 grains per gallon. That is classed as hard, and minerals like that crust over drain valves and settle as a layer of sediment on the tank floor.
Often the puddle is the first thing anyone spots. Most of the guidance below applies whether the heater is in a basement utility room, a hall closet or the garage.
What comes first when the tank starts dripping?
Start with the steps in the emergency box above, then spend two minutes working out where the water is really coming from. Those two minutes change the price and the urgency.
- Valve type: a lever handle closes with a quarter turn, while a round wheel handle has to be turned clockwise until it stops.
- Towel test: wipe the jacket, the fittings and the floor completely dry, then watch. The spot that gets wet first is the source.
- Power check: on an electric heater, switch the breaker off before you touch the access panels on the side.
If you smell gas at any point, skip all of that. Leave the house, call 911, then phone your gas company from outside. The City lists two gas companies for Overland Park, so use the leak number printed on your own gas bill or the ones in the emergency box above.
Where is the water coming from?
A leak starts at one of five places, listed here from the top of the tank down. The first four can generally be repaired, and the fifth means the tank is finished.
- Top connections: the hot and cold fittings or flexible connectors weep at the threads and the water runs down the jacket.
- Relief valve: drips from the discharge pipe suggest high pressure, high heat or a tired valve seat.
- Element gasket (electric): a damp side panel or a rust streak below it means a gasket is seeping.
- Drain valve: the spigot near the floor gets crusty with scale and stops sealing.
- Tank body: water seeping from a seam or welling up under the base means the steel has rusted through.

Water from a top fitting often runs down and pools at the base, so people blame the tank. That is why the dry-and-watch step matters.
Is a leaking water heater an emergency?
Yes when it sits above living space or the water comes from the tank itself, and not quite as pressing when a small drip lands on a bare basement slab. Even then it will not stay small.
A heater in a finished basement or a main-floor closet can soak carpet, drywall and the framing behind it in an afternoon. Once rust breaks through a tank wall, every heating cycle widens the hole.
- Pressure keeps pushing: even with the supply closed, the water already in a tank can empty itself through a hole in the bottom.
- Pans need a clear drain: a drain pan only helps if its line is open, and a clogged line lets the pan overflow.
- Hidden damage: a slow leak behind a closet wall can run for weeks before the stain appears.
Can a leaking water heater be repaired?
A leak at a fitting, the relief valve, the drain valve or an element gasket can be repaired. A leak from the tank body cannot be, so the job becomes a replacement.
| Repair | National average range | What it means |
|---|---|---|
| Relief valve | $35–$250 | drips from the side pipe |
| Anode rod | $100–$250 | rusty or smelly hot water |
| Expansion tank, installed | $225–$625 | relief valve keeps weeping |
| Typical repair visit | $200–$850 | about $550 on average |
| Leak from the tank bottom | replacement | the lining has failed |
Those are national averages, rounded, and here is how they are worked out. A tank replacement nationally runs about $1,000 to $3,400 installed, and the replacement cost guide breaks that down by tank size.
Not sure if it is a fitting or the tank? Describe the drip by call or text.
What does a dripping relief valve pipe mean?
The relief valve opens when pressure or temperature inside the tank climbs too high, and the pipe beside it carries that water down toward the floor. Regular dripping is a symptom worth chasing, not a nuisance to ignore.
Three causes come up most often:
- A closed plumbing system: if a check valve or pressure-reducing valve sits on the cold supply, heated water has nowhere to expand unless an expansion tank absorbs it.
- A worn-out expansion tank: nationally these are replaced every 5 to 10 years, and a waterlogged one stops cushioning pressure.
- A hot setting: the Consumer Product Safety Commission urges 120°F, and a hotter setting raises pressure and scald risk together.
Never cap or plug that pipe, because it is the safeguard against a tank overheating and rupturing.
Does replacing a leaking heater need a permit?
Yes. The City's permits page says a permit is required to add or replace a water heater, and many permits go through its online the City's online permitting system (ePLACE) system. Ask who files it and whether your quote includes it as its own line.
- Emergency swaps: ask permit services how an after-hours replacement is filed; the permit is still required.
- Fee: the published schedule starts at $30 for projects valued under $5,000, so ask the City what applies to a heater.
- Questions: City permit services answers at 913-895-6220.
The permits guide covers licensing and what to ask.
What details help the first call?
Four details make the first conversation quick and the price accurate. Jot them down while the tank drains or dries.
- The spot where fresh water first appears: top fittings, side pipe, drain valve or base
- Whether the unit burns gas or runs on electricity, and if the fuel is off yet
- The size and manufacture date on the label on the tank's side
- Where it sits: basement, closet, garage or utility room
Tell us what's going on and you'll hear back with a price before anyone touches the tank. Before work starts, look up the contractor in Johnson County's license search, which the permits guide walks through.
Water on the floor right now? Call or text any hour for a callback.
Questions homeowners ask
Can I leave a leaking water heater on overnight?
No. A tank leak widens each time the heater cycles, so close the cold-water valve above the tank and turn the gas control to off or flip the breaker before bed.
Why is water coming out of the pipe on the side of the tank?
That pipe carries discharge from the temperature and pressure relief valve. An occasional drip points to high pressure or a worn valve, while a steady stream needs attention today.
Is a small puddle under my water heater an emergency?
It is if the heater sits over finished space or the water is coming from the tank body. In an unfinished basement corner a small puddle is less urgent, but it still grows.
Can a water heater leak be repaired?
A leak at a fitting, valve or element gasket usually can be. Water seeping from the tank itself cannot be patched, and that means replacement.
What does a leak repair usually cost?
Across the country a repair visit runs about $200 to $850, with a relief valve alone at $35 to $250. Local prices vary with the part and the access, and yours is stated before work begins.
Last updated: